Smok Nord 2 User Guide - New Zealand

7ZO2MYVKTlissoCPtLll_smok-nord-2-temp-image-red_5000x.jpg

 

SMOK – Nord 2 Refillable Pod Kit 

The SMOK Nord 2 is the new and improved version of the SMOK Nord. If you liked the original device you will enjoy the upgrades they have made with this one. 

They have increased the battery power from 15W to 40W as well as introducing adjustable wattage. The power range of the Nord 2 can be adjusted by pressing the power button 3 times.  

The new Nord 2 has a 0.69inch OLED display screen on the side that shows concise vaping data, including the battery life, wattage and coil resistance, and each pod cartridge is a larger size 4.5ml. 

 

There are 9 exciting colour options to choose from: 

  • Red
  • Black Cobra
  • 7 Colour Oil
  • Gold
  • 7 Colour Cobra
  • White Cobra
  • 7 Colour Resin
  • Black Stabilising Wood
  • Red Stabalising Wood

 

The SMOK Nord 2 kit includes: 

  • 1 x nord 2 device (1500mAh)
  • 1 x nord 2 RPM Pod Cartridge 4.2ml Mesh 0.4 coil
  • 1 x nord 2 nord Pod Cartridge 4.2ml DC 0.8 MTL coil
  • 1 x USB Cable
  • 1 x user manual
  • 1 x warranty card

SMOK Nord Coils 

Nord 2 RPM Mesh pod cartridge 4.5ml 0.4 coil: 

This pod is best for direct to lung vaping. RPM mesh pods have more airflow and are best for lower mg nicotine salt e-liquids. The coil is preinstalled and are replaceable so there is no need to replace the whole pod, just the coil. 

 

Nord 2 nord pod cartridge 4.5ml DC 0.8 MTL coil: 

This pod is best for mouth to lung (MTL) vaping. It is best for higher mg nicotine salt e-liquids. The coil is preinstalled and are replaceable so there is no need to replace the whole pod, just the coil. 

 

To fill each 4.2ml pod cartridge: 

Lift the small black rubber plug on the side of the pod and inject your nicotine salt e-liquids in until full. When it is full, close the plug firmly and wipe any spillages with a tissue. Wait 10 minutes for the nicotine salt e-liquid to soak into the coil properly so that you don’t risk burning up and ruining the coil. 

 

Operating the SMOK Nord 2 device: 

Firstly, remove all stickers on the pod cartridges and the device. Place the full pod cartridge onto the device until it clicks into place. Once it is in place quickly press the fire/power button 5 times in 2 seconds to turn it on. The white led light on the fire/power button will flash 3 times.  

To turn the power off, repeat the last step and the device will read “Goodbye.” 

Once the device is turned on the screen will display “SMOK” and the version number and then it will enter the main interface which will display the wattage setting, puff setting, battery percentage and estimated charge time. 

 

Charging the SMOK Nord 2 device: 

Insert the USB cable provided by plugging it into the bottom of the device. Plug the other end into a USB port, for example, computer USB port or Mobile phone adaptor.  

While the device is being charged the charging interface will appear and display the battery percentage and the estimated charge time remaining. The white light on the fire/power button will flash once. 

Once it is fully charged unplug the USB cable from the device. Quickly press the fire/power button 3 times to set the wattage. Click or long press the fire/power button to set to your required wattage setting, between 1W – 40W. 

 

Puffs counter - OLED display screen: 

When the pod is removed from the device the number of puffs will be automatically cleared. When the puff counter reaches 999P it will automatically clear also. 

 

Vaping: 

To vape using the mesh coil, inhale directly to lungs while pressing the fire/power button.  

To vape using the nord coil we recommend mouth to lung (MTL) for nicotine salts. 

 

Important note: 

To ensure your coil lasts, always check and make sure there is enough nicotine salt e-liquid inside the pod before vaping. Otherwise you risk burning out the coil.

Was this article helpful?
1 out of 1 found this helpful